Do you need to repair your TA-2530B Husky 8 Gal Air Compressor? Looking for the Husky 8 Gallon Air Compressor TA-2530B Parts? Then You have come to the right place.
Here you can find full parts list for Husky TA-2530B Model and an image with the locations of each part on the air compressor.
Husky TA-2530B Parts List – Table A
| # | Description | Kit # | Part # | Qty |
|---|---|---|---|---|
| 1 | Head bolt, M80×105 | 4 | ||
| 2 | Washer, lock 8mm | 4 | ||
| 3 | Cylinder head | 03-100 | 1 | |
| 4 | Fitting, tee | 40-033 | 1 | |
| 5 | Gasket head | C | 35-060 | 1 |
| 6 | Valve, Assy. | B | 11-004 | 1 |
| 7 | Pin, dia. 3×6mm | B | 2 | |
| 8 | Valve, reed, inlet | B | 34-001B | 1 |
| 9 | Gasket, cylinder upper | C | 35-061 | 1 |
| 10 | Piston | A | 28-012 | 1 |
| 11 | Cylinder | 10-004 | 1 | |
| 12 | Gasket, Cylinder lower | C | 35-062 | 1 |
| 13 | Ring, compression | A | 29-021 | 2 |
| 14 | Ring, scraper | A | 1 | |
| 15 | Pin, piston dia. 12mm | A | 30-003 | 1 |
| 16 | Ring, snap 12mm | A | 46-005 | 2 |
| 17 | Eccentric | A | 12-004 | 1 |
| 18 | Rod, connecting | A | 03-032 | 1 |
| 19 | Bolt, SHCS, M8×22–LH | A | 45-154 | 1 |
| 20 | Bolt, SHCS, M5×0.8×15 | 6 | ||
| 21 | Oil fill cap M16×1.5 | 26-004C | 1 | |
| 22 | Oil sight gauge | D | 33-002 | 1 |
| 23 | Seal, oil sight gauge | D | 1 | |
| 24 | Cover, crankcase | 03-101B | 1 | |
| 25 | Baffle, rubber | 36-015 | 1 | |
| 26 | Motor, assy. | 1 | ||
| 27 | Capacitor, running, 120 μF | 27-031 | 1 | |
| 28 | Washer, lock 3mm | 2 | ||
| 29 | Screw, M3×6 | 2 | ||
| 30 | Washer, tooth lock, 8mm | 1 | ||
| 31 | Nut, M8×1.25 | K | 7 | |
| 32 | Plug, oil, M12×16 | 45-051B | 1 | |
| 33 | Valve, relief | 40-018B | 1 | |
| 34 | Fan, AL alloy | 03-109 | 1 | |
| 35 | Nut, M6 | 1 | ||
| 36 | Bolt, SHCS, M6×16 | 1 | ||
| 37 | Ring, snap. 14mm | 1 |
Husky TA-2530B Parts List – Table B
| # | Description | Kit # | Part # | Qty |
|---|---|---|---|---|
| 38 | Screw, ST4. 2×12 | 2 | ||
| 39 | Screw, with washer, M5×512 | 2 | ||
| 40 | Shroud | 06-063 | 1 | |
| 41 | Strain relief 6W–3 | 21-040 | 2 | |
| 42 | Air filter | 41-005 | 1 | |
| 43 | Bolt, hex head, M8×30 | 4 | ||
| 44 | Washer, flat, 8mm | K | 12 | |
| 45 | Washer, lock, 8mm | 4 | ||
| 46 | Tank, 8 gal. | 1 | ||
| 47 | Check valve | 38-001A | 1 | |
| 48 | Drain valve, 1/4 in. NPT | 39-020A | 1 | |
| 49 | Nut, rivet, M6 | E | 45-086 | 4 |
| 50 | Washer, flat, 6mm | 4 | ||
| 51 | Screw, SHCH, M6×20 | 4 | ||
| 52 | Handle | E | 08-108B | 1 |
| 53 | Washer, flat, copper, 10mm | F | 46-029 | 2 |
| 54 | Nut, hex, compression, G3/8 | F | 44-003 | 2 |
| 55 | Tube, outlet, OD 10mm | F | 43-017C | 1 |
| 56 | Fin, ID 10mm | F | 1 | |
| 57 | Tube, relief OD 6mm | G | 43-017F | 1 |
| 58 | Nut, hex, compression, G1/8 | G | 44-001A | 1 |
| 59 | Switch, pressure, 95–125 PSI | 21-011A | 1 | |
| 60 | Pressure gauge, 200 PSI, 1/8 in. NPT | 23-018 | 1 | |
| 61 | Pressure gauge, 200 PSI, 1/4 in. NPT | 23-038 | 1 | |
| 62 | Nipple,1/4 in. NPT×48mm | 42-028 | 1 | |
| 63 | Valve, safety, 140 PSI, ASME, 1/4 in. NPT | 24-010 | 1 | |
| 64 | Nipple, 1/4 in. NPT×30mm | 42-026E | 1 | |
| 65 | Regulator, 1/8 in. NPT×1/4 in. NPT | 25-053 | 1 | |
| 66 | Quick connect, one-touch, 1/4 in.NPT | 42-080 | 1 | |
| 67 | Isolator, rubber | K | 15-014 | 2 |
| 68 | Bolt, hex head. M8×20 | K | 2 | |
| 69 | Nut, hex head, M10 | H | 2 | |
| 70 | Washer, lock, 10mm | H | 2 | |
| 71 | Wheel 6 in. | H | 15-070 | 2 |
| 72 | Shoulder bolt, OD15,5×36.5×M10 | H | 46-041 | 2 |
| 73 | Cord, power, SJT14/3 | I | 22-005 | 1 |
| 74 | Terminal, Y type 1.5–40 | I | 2 | |
| 75 | Terminal, O type 1.5–40 | I | 1 |
*Note: Items without a part number or kit letter are not available. Items with a kit number are only available as part of a kit.
Kits – Table C
| Kit | Description | Qty |
|---|---|---|
| A | Handle | 1 |
| B | Manual AUTO/OFF switch | 1 |
| C | Safety valve | 1 |
| D | Wheel | 2 |
| E | Tank | 1 |
| F | Quick coupler | 1 |
| G | Pressure regulator knob | 1 |
| H | Tank pressure gauge | 1 |
| I | Regulator pressure gauge | 1 |
| J | Rubber foot | 2 |
| K | Drain valve | 1 |
| L | Air filter | 1 |
| M | Oil bottle | 1 |
Hello!
My compressor started only building pressure up to 40psi. I took the top of the head off and removed the U shaped valve cover and the reed was broken on both ends. Looking at the diagram it doesn’t show a part number for just the reed. I imagine I’ll need to replace the valve reed i key as well. If I’m reading this right it should all be part of the B kit but I can’t find a price anywhere. If it is all just part of the kit I’ll need to order the kit.
Thanks in advance!
Thank you for having a diagram and part numbers for everything I need